|本期目录/Table of Contents|

[1]王成刚,肖健,刘慧,等.格莱圈密封性能非线性有限元分析[J].武汉工程大学学报,2014,(02):42-48.[doi:103969/jissn16742869201402009]
 WANG Cheng gang,XIAO Jian,LIU Hui,et al.Finite element analysis of sealing performance of Glydring seals[J].Journal of Wuhan Institute of Technology,2014,(02):42-48.[doi:103969/jissn16742869201402009]
点击复制

格莱圈密封性能非线性有限元分析(/HTML)
分享到:

《武汉工程大学学报》[ISSN:1674-2869/CN:42-1779/TQ]

卷:
期数:
2014年02期
页码:
42-48
栏目:
机电与信息工程
出版日期:
2014-02-28

文章信息/Info

Title:
Finite element analysis of sealing performance of Glydring seals
文章编号:
16742869(2014)02004207
作者:
王成刚1肖健1刘慧1刘俊1高兴1盖超会2
1.武汉工程大学机电工程学院,湖北 武汉430205;2.武汉软件工程职业学院机械制造工程系,湖北 武汉430205
Author(s):
WANG Chenggang1XIAO Jian1LIU Hui1LIU Jun1GAO Xing1GAI Chaohui2
1.School of Mechanical and Engineering ,Wuhan Institute of Technology,Wuhan 430205,China;2.Department of Mechanical Manufacture Engineering,Wuhan Vocational
关键词:
格莱密封圈压缩率最大接触压力非线性有限元分析
Keywords:
College of Software and EngineeringWuhan 430205China Glydringcompression ratiocontact pressurenonlinear finite element analysis
分类号:
TH138
DOI:
103969/jissn16742869201402009
文献标志码:
A
摘要:
为了研究气缸密封件的性能以及失效情况,运用有限元分析方法对格莱圈弹性体进行分析.利用有限元分析软件建立了格莱圈有限元分析模型,通过建模、划分网格、加载、求解以及后处理等步骤,对其在不同压缩率、不同气压时密封面接触压力分布规律进行探讨分析,确定格莱圈易失效位置,分析压缩率和气压对格莱圈密封面最大接触压力的影响.结果表明:在位移云图和接触压力云图中,格莱圈密封面最大接触压力随压缩率和气压的增加而增加;格莱圈的方型圈与缸套的接触压力最大,且最大接触压力明显大于通入气体的压力,故格莱圈不易失效;气缸在实际气压0.4 MPa和8%压缩率的情况下能正常工作,为评定缸阀一体化气缸的可靠性提供了参考.
Abstract:
To investigate the performance and the failure place of cylinder seals,the finite element analysis method was used to analyze Glyd sealing ring elastic and ANSYS was used to establish model of Glyd sealing ring.The distribution of the sealing surface contact stresses was discussed and the place of failure was determined in the different compression ratios and in the different gas pressures after modeling,meshing,loading,solving and postprocessing etc..The influences of compression ratios and gas pressures on the maximum contact stress were analyzed.The results show that the maximum contact pressure of Glyd ring sealing surface increases with the increase of compression ratio and gas pressure;the contact pressure reaches the maximum at interface of the cylinder liner and the square ring of Glyd,which is significantly greater than that of the gas,so the Glyd will not failure;the cylinder can work normally in the actual 0.4 MPa gas pressure and 8% compression ratio,which provides reference to assess the reliability of the cylinder valve integrated cylinder.

参考文献/References:

[1]贺庆平,张付英,沈晓斌.基于有限元分析的液压往复密封优化设计[J].机械设计与制造,2008(7):68.HE Qingping,ZHANG Fuying,SHEN Xiaobin.Optimization of sealing o ring based on finite element analysis[J].Machinery Design & Manufacture,2008(7):68.(in Chinese)[2]严桃平,赵迎生.新型组合密封圈的密封机理及其应用[J].机床与液压,2003(1):244245.YAN Taoping,ZHAO Yingsheng.Sealing principle of new type combined seal and its application[J].Hydromechatronics Engineering,2003(1):244245.(in Chinese)[3]喻九阳,高九阳,王成刚,等.机械振打器活塞杆处0形圈不同密封结构下的性能分析[J].润滑与密封,2010,35(3):6568.YU Jiuyang,GAO Jiuyang,WANG Chenggang,et al.Analysis of sealing performance of Oring with different structure for piston rod of rapping device[J].Lubrication Engineering,2010,35(3):6568.(in Chinese)[4]陈以文,喻九阳,谢洪波,等.自动振打除灰装置活塞处双向密封研究[J].武汉工程大学学报,2011,33(10):7780.CHEN Yiwen,YU Jiuyang,XIE Hongbo,et al.Comparative analysis and selection for sealing slructure between piston and rod of rapping dewice[J].Journal of Wuhan Institul of Technology,2011,33(10):7780.(in Chinese)[5]李振涛,孙鑫晖.O形密封圈密封性能非线性有限元数值模拟[J].润滑与密封,2011,36(9):8690.LI Zhentao,SUN Xinhui.Finite element numerical simulation of the sealing performance of Oring seals[J].Lubrication Engineering,2011,36(9):8690.(in Chinese)[6]Fired I,Johonson A R.Nonlinear computation of axisymmetric solid rubber deformation[J].Computer Methods in Applied Mechanics and Engineering,1998(67):241253.[7]Nikas G K.Elastohydrodynamics and mechanics of rectangular elastomeric seals for reciprocating piston rods[J].ASME J.Tribol.,2003(125):6069.[8]Nikas G K,Sayles.Nonlinear elasticity of rectangular elastomeric seals and its effect on elastohydrodynamic numerical analysis[J].Tribol.Int.2004,37:651660.[9]高九阳,喻九阳,王成刚,等.沟槽对O形圈密封结构性能的影响[J].武汉工程大学学报,2010,32(7):7880.GAO Jiuyang,YU diuyang,WANG Chenggang et al.Effects of grooves on sealing performance of Oring seal structure [J].J. Wuhan Inst.Tech,2010,32(7):7880.(in Chinese)[10]周恩涛,李建勋,林君哲.液压缸活塞密封性能的有限元分析[J].润滑与密封,2006,176(4):8489.ZHOU Entao,LI Jianxun,LIN Junzhe.Fin ite element analysis of piston seals property of hydraulic cylinders[J].Lubrication Engineering,2006,176(4):8489.(in Chinese)[11]张婧,金圭.O形密封圈接触压力的有限元分析[J].润滑与密封,2010,35(2):8083.ZHANG Jing,JIN Gui.Finite element analysis of contact pressure on Oring[J].Lubrication Engineering,2010,35(2):8083.(in Chinese)[12]谭晶,杨卫民.O形橡胶密封圈密封性能的有限元分析[J].润滑与密封,2006,181(9):6569.TAN Jing,YANG Weimin.Finite element analysis of the sealing performance of Oring seal structure[J].Lubrication Engineering,2006,181(9):6569.(in Chinese)

相似文献/References:

[1]郑小涛,文 翔,桑 聪,等.高温波齿复合垫片的循环压缩回弹性能[J].武汉工程大学学报,2016,38(4):382.[doi:10. 3969/j. issn. 1674?2869. 2016. 04. 013]
 ZHENG Xiaotao,WEN Xiang,SANG Cong,et al.Cyclic Compression-Resilience of Flexible Graphite Corrugated Metal Gaskets at High Temperature[J].Journal of Wuhan Institute of Technology,2016,38(02):382.[doi:10. 3969/j. issn. 1674?2869. 2016. 04. 013]
[2]王成刚 肖健 刘慧 刘俊高兴盖超会.格莱圈密封性能非线性有限元分析[J].武汉工程大学学报,2014,(02):10.
 WANG Cheng-gang XIAO Jian LIU Hui LIU Jun GAO Xing GAI Chao-hui.Finite element analysis of sealing performance of Glyd-ring seals[J].Journal of Wuhan Institute of Technology,2014,(02):10.

备注/Memo

备注/Memo:
收稿日期:20131216基金项目:国家自然科学基金项目(50976080);武汉工程大学科学研究基金(NO.CX201229)作者简介:王成刚(1974), 男,湖南祁东人,副教授,博士.研究方向:应力分析、计算机测控技术、PLC控制;新型化工设备的研究与开发.
更新日期/Last Update: 2014-03-20