|本期目录/Table of Contents|

[1]谈文鑫,廖义德*,郭敏,等.汽车动力转向油罐盖滚边力计算及试验研究[J].武汉工程大学学报,2011,(09):93-95.
　TAN Wenxin,LIAO Yide,GUO Min,et al. Calculation and experimental investigation of roller hemming pressure in a power steering oil tank cap of automobile[J].Journal of Wuhan Institute of Technology,2011,(09):93-95.
点击复制

汽车动力转向油罐盖滚边力计算及试验研究(/HTML)
分享到：

《武汉工程大学学报》[ISSN:1674-2869/CN:42-1779/TQ]

卷:
期数:
2011年09期
页码:
93-95
栏目:
机电与信息工程
出版日期:
2011-09-30

文章信息/Info

Title:
 Calculation and experimental investigation of roller hemming
pressure in a power steering oil tank cap of automobile
文章编号:
16742869(2011)09009303
作者:
谈文鑫; 廖义德*; 郭敏; 陈方; 邹军军
武汉工程大学 机电工程学院，湖北 武汉 430074
Author(s):
TAN Wenxin; LIAO Yide; GUO Min; CHEN Fang; ZOU Junjun
School of Mechanical & Electrical Engineering, Wuhan Institute of Technology, Wuhan 430074, China
关键词:
冷滚压; 油罐盖; 滚压力; 数学模型
Keywords:
cold rolling;  oil tank cap;  rolling pressure;  mathematical model
分类号:
TG302
DOI:
-
文献标志码:
AAdoi:10.3969/j.issn.16742869.2011.09.023
摘要:
加工汽车动力转向油罐盖安装密封圈的槽一般采用冷滚压的方法,对其滚压力的求解暂时还没有成熟的计算公式，常采用经验公式法和实验法.根据油罐盖受滚压时的变形特点，建立了滚压力理论计算的简化数学模型，并用相应的滚压实验进行了验证，解决了经验公式法和实验法存在的求解不准确、周期较长，成本很高等问题.
Abstract:
The groove processing of the power steering oil tank cap often takes the method of cold rolling, whose products are used to install seal circles. There is no mature formula to calculate the solutions of the rolling pressure at present, so the empirical formula method and experimental method are always used. An academic calculation is in accordance with mathematical model, which is based on the deformation characteristics when the oil tank cap is rolled was established.The results from the corresponding experiments show that it solves some problems such as lack of accurate calculation, long calculation cycle, high cost and so on when the empirical formula method and experimental method are used.

参考文献/References:

［1］郭长江,杨改云,赵利德.滚压成形力的数值计算与模拟［J］. 机床与液压,2007,35(10):101102.
［2］顾青丽. 风电螺栓螺纹滚压工艺参数的选择［J］.电气制造,2010(10):6264.
［3］张守茁,席镇,孙海花,等.圆筒形件拉深过程的力学理论分析与计算［J］.内蒙古工业大学学报:自然科学版,2006,25(3):183189.
［4］ 关桂芳,刘志坚,郭金基,等. 计算冷挤压成型钢盔挤压力的滑移线法［J］.暨南大学学报:自然科学版,1999,20(1):3437.
［5］ 卢险峰,谭欣珍,周勇,等.拉深变形力理论计算模型研究［J］.中国机械工程, 2008,19(16):20042006.
［6］李尧.金属塑性成形原理［M］.北京: 机械工业出版社,2004.
［7］ 卢险峰,周勇,盛自强.考虑冷变形加工硬化的翻边力理论计算［J］.南昌大学学报:工科版,2009,31(2):187191.

相似文献/References:

备注/Memo

备注/Memo:
-
更新日期/Last Update: